Category: Sea House Salvage

Humble Lighting, Cats

11 Comments

kitchen_lighting_01_123017

I got my lighting order from Evan Design: replacement chip LEDs for the under shelf, and five 3mm LEDs for the pot lights (3/16-inch brushed aluminum eyelets) in the ceiling. Look at how warm the “warm white” is!

kitchen_lighting_123017

And gah! Look at what a tangle the backside is. There’s five chip LEDs (the tiny red and green magnet wires) and five 3mm LEDs, wired to two 3V battery holder/switches. I’m posting this in all humility and baby steps learning. I *will* get better at wire stripping and making elegant connections. Because how I love learning new things?! Even though I cringe at being clumsy and awkward doing so.

Scarlett_123017

Speaking of elegant connections… I went to post this at my main workstation, but found Scarlett snugged in my chair (and absorbing the under desk Dyson heater warmth). Of course I could not disturb her, so I retreated to the couch with my laptop.

Albie_laundry_123017

And there was Albie, snugged into a fresh, warm load of laundry waiting to be folded. So now I’m arrayed on the other end of the couch, with laptop, phone, sketchbook, freshly sharpened Blackwing pencil, two reference books, a baggie of lighting components, and a glass of wine, all amid the piles of half-folded laundry. Same as it ever was,

The Solstice, Lighting

10 Comments

solstice_122117

Last night — Good Solstice, all! — I set to work installing the ceiling lights in the Sea Rise Pavilion kitchen.

lights_122217_00

Because I’m such a lighting electrics n00b, I used five 3-volt chip LEDs, set in mini eyelets. They are tragically insufficient to light the kitchen. But hey! I learn by doing. So I went to bed.

lights_122217_01.jpg

This morning, I ordered some larger (3mm) LEDs, then pulled the chip LEDs and eyelets from the ceiling installation. (Those are the holes you see.) Under-shelf lighting seemed like a good use of the sadly pale chips, so I plotted a layout in Illustrator to use as a template, and drilled new holes in the upper shelf. (Um, not an ideal construction protocol, the drilling of already-installed things.) I methodically undid all the twisty magnet wire connections from the ceiling — thankfully I had not set the heat shrinks — and reset the eyelets under the shelf. With my teensiest drill bit I made exit holes for the wires in the back wall, in line with each eyelet.

It is a good setup, but two of the chip LEDs did not fully survive. (Though they do work intermittently, argh, whygodwhy?)

sunset_122217

Then I walked out to see this sunset over the ocean. One can aspire.

 

Wrought Iron Sign Salvage

10 Comments

SH_roof_122017

I wrought Sea House emblems for the landward and sea-facing sides of the pavilion roof. They’re meant to be salvage from the old Sea House Pleasure Pier and Estate. And so they are.

SH_logo_roof_122017.jpg

Sized to fit between the raised seams on the metal roof, I cut seven copies of the emblem from 65 lb. black cardstock and glued them together. After drying under weight, I sanded the edges even, and slightly beveled the top edges. I added fastening “bolts” then lightly stippled and dry brushed some wear and weathering. Not too much. The caretaker is diligent about her conservation duties.

front_122017

Then I had to make a smaller version to mount on the fireplace.

SH_fireplace_122017

It looks splendid, don’t you agree? (Well, except for the ripply rug. There’s always something.)

kitchen2_122017

I bashed out the support column in front of the kitchen, and felt much better about the space, even though it still looks like every other ELF kitchen ever made, ever. (Not that there’s anything wrong with that.) I’ll scrape away the brackets on the floor, patch where the post was, and it’ll be an intentional remodel artifact :) I found the LED pot lights I ordered, then lost, so next step will be the ceiling/roof, and then the exterior siding.

gh_122017.jpg

In the greenhouse, the hydroponics have been relocated to an anchored barge just off the rear utility deck.

lowercase_n_121817

Meanwhile, I got to open an early present, a vintage sign hollow aluminum lowercase n, about 12 tall by 3 inches deep. Feeling the love. Thank you, my B.

Boxen, Handles, Slipcases

8 Comments

FF24_pavilion_02

There’s a new set of boxes over at MMS+S, reminiscent of the “dish pack” size, for all your miniature packing needs.

I installed ELF handles set in reversed eyelets on the Sea Rise Pavilion front doors, and then glued the whole panel into the frame. I think I’ve finally worked out which components will be attached together, and which will remain removable. Rethinking having the hydroponics inside the greenhouse; they might get moved to the lower back utility deck. There is still much I don’t know.

slipcases_kitchen

Working on a simple slipcase kit to fit single and triple sketchbooks, in the classic and smaller sizes. Adds a nice finishing touch, and keeps your shelves and bookcases looking tidy. (And yes, that’s an April Wright mug — her pottery is wonderful! The wee bear bowls being used as bookends are feves from Laurel’s ValueARTifacts shop.)

Other stuff in progress and in sketch phase, brimming and swimming with ideas and plans. Focusing now on finishing up work projects for the year, and spending the holidays with family, and taking some time off.

Be good to yourselves, dear imaginary friends!

 

 

 

Pavilion Remodel: Kitchen Progress

12 Comments

kitchen_120417.jpg

This is the first time I’ve ever made fake “fixed door” cabinets, and I confess I feel like I cheated to achieve a look, and/or once again betrayed my core values for the sake of… <fill_in_the_blank>

However, I really do have a bigger picture for this set/build, so faux kitchen doors and drawers are just fine. I am more than pleased with the ELF sink, tap, handles and two-burner electric stovetop. After futzing with the door/drawer front layout in Illustrator, I cut all the pieces from a single length of eggshell white-stained basswood with pretty grain. I sanded the “opening” edges ever-so-slightly to distinguish, and made templates to drill for the ELF handles. Using pliers to gently make the handles fit helped a lot.

I’m still considering the lighting/windows/shelving/roof design of this module. I know, that’s a lot to still be figuring out at this stage, and welcome to my world. I’m off to Santa Cruz for a few days tomorrow, so I’ll have some good thinking time on my drive to ideate.

Also, the perfect mug and plate on the countertop is from Keli’s friend April Wright, a miniature ceramicist working in 1:12 scale.

Sea House Pavilion Remodel: Flitting About

24 Comments

front_exterior_111717

I finished planking the Sea House Pavilion front entry remodel — though there are still stain touchups to do. This build is very different in that components will remain modular, to facilitate access and photography, rather than be a single, connected structure.

front_110617

Inside walls are stained eggshell white. The main living area ceiling (the underside of the sleeping loft) is in, made from bead-board paneling. (Here barely seen, as IRL).

front_interior_110617

You can glimpse the original Pavilion roof ceiling, now lifted to accommodate the sleeping loft.

front_interior2_110617

A view of the sleeping loft addition, and a roughed-in kitchen wing and shower stall (fireplace removed.)

loft_floor_111117

After deliberation, I chose varnished cork for the sleeping loft floor, which occupies three bays. Many more decisions remain, especially since I’m thinking ‘nest’ rather than traditional bedroom. Think ‘sleeping in a pile’ (my favorite!) from Where The Wild Things Are. Because post-sea-level-rise living will probably benefit from that.

elf_trolley_111917

I made my first-ever ELF Miniatures order, for this kitchen trolley kit, as well as an under-counter sink and 2-burner stovetop surface for the kitchen wing. I am smitten.

kitchen_3walls_111517.jpg

The kitchen wing occupies two bays, and will have a countertop with sink, prep area and the two-burner electric stove (powered by rooftop solar panels.) There’ll be non-opening cupboards below, and an under-counter refrigerator. Two walls are paneled in horizontal bead-board, to which there will be shelves attached; the third wall is papered in the same vintage San Francisco map as the ceiling. The window is made from this weird thick glass disc, a bag of which I found in the crap/craft store.

hydroponics_planning

Moving on to greenhouse hydroponics. I did a bunch of research to arrive at an aggregate vision of what a system might look like on an off-the-grid tiny home scale. The grow vats are restaurant jam tubs. I made some wonderful Georgie Steeds lettuce and cabbage kits, and from there worked out optimum growing layouts. I fiddled with the vat top layouts, and used the Cricut machine to cut the final patterns.

hydroponics_lettuce_cabbage

I noticed many hydroponic systems had these sort of “grow rings” around the cutouts. They appeal to my graphic sensibility, so I laboriously added them to the system. They can barely be seen beneath the lush growth, but we and the devas know they are there.

hydroponics_rings

To the greenhouse I added rails and slats to support the grow vats. I’m experimenting with wire and shrink tubing to evoke a water and nutrient circulation system. One of the challenges is keeping each of the wings modular, yet connected as a whole. In that the greenhouse and kitchen wings need to connect to the solar panels and water collection systems located on the pavilion roof and aft deck. As do the roof gutters need to funnel rainwater into the cisterns located under the pavilion. And so on.

hydroponics_111717

I leave you with a view of Georgie Steeds’ Nasturtium kit. It’s just barely finished, plonked in a Braxton Payne pot and glop-waxed to the bench. I love nasturtiums; they’re ubiquitous in NorCal gardens. I’d very much like to twine these throughout the greenhouse wing, while also keeping it detachable. We’ll see.

nasturtium_111517

 

Sea House Pavilion Remodel: Front Entry

22 Comments

front_102917

Work has begun on framing in the front entry, using 3/8-inch stock to match the existing structure. I chose a set of Houseworks French doors, installed backwards so they open outward. There will be a 5-inch wide transom window above. The door woodwork is finished in an eggshell white stain, and the two side panels will be reclaimed weathered gray horizontal planking.

front_transom_source

I got curious about the line weights in intricate pattern that I might successfully cut (and remove from the mat) on the Cricut, and got down to 6 points (.083-inch / 2.1 mm). This seems a good scale for the narrow panels of the doors and transom (the greenhouse window leading is 9 points (.125- inch / 3.2 mm).

inside4_102917

The difference in scale between the front doors and the greenhouse windows makes sense (especially now that I know I can cut finer line weights). The interior front wall will be planked in the eggshell white stain, with a matte varnish.

inside5_102917

Now I’m thinking on how the ceiling between the main floor and the sleeping loft will work, and how to finish out the fireplace through to the roof — some tricksy geometries. I ordered a bunch of vegetable kits from Georgie Steeds at The Miniature Garden — my favorite miniature plant kit purveyor — to populate the long shelf in the greenhouse. The interior greenhouse windows are open to the room so the potted trees can reach out.

gh_inside_102917

Also, how is it almost November?!

 

 

 

Sea House Pavilion Remodel: Greenhouse Wing Leaded Glass Windows Complete

22 Comments

greenhouse_102717

The leaded glass windows for the Sea House Pavilion greenhouse wing are completed and installed.

greenhouse_2_102717

Here’s a mildly different view. (It’s late, and my studio lighting is rubbish.) But if you were the caretaker of an historic heritage seaside resort that was abandoned because of sea level rise, wouldn’t you want a place to grow fresh greens and fruit to supplement your subsistence gatherer lifestyle?

I know I would.

gh_all.jpg

And I would want it to be beautiful.

 

Sometimes, things work out better than hoped for

19 Comments

gh_front_03

The topic of this and last week’s Santa Cruz commute thinking time was about how to render the Sea Rise Sea House Pavilion’s greenhouse windows. I knew I wanted to do something leaded (or leaded-esque), and I knew the inevitable off-square measurements of the actual structure would be a nightmare to fit.

gh_front_04

I’ve built two wing extensions on either side of the main deck to increase the living space area. One side is the greenhouse, and the other will be the shower and sleeping alcove. For the greenhouse leaded glass, I drew my designs using 9-point (1/8-inch) lines, which seem reasonably robust for a seaward structure. They’re cut from black cardstock, and glued front and back to non-glare Plaskolite, which provides a semi-opaque — and salt-spray burnished — surface.

gh_front_02

My initial approach was to tediously center the Plaskolite within the 3/16-inch framing. (Of course if I was more dedicated, I would have routed a channel in the one million each of the frames, or, have built them with three layers of stock. But I’m not.) As I was fiddling about with measurements and drawing and cutting prototypes, I realized the best — and squarest — way is to cut the panes and cardstock leading a scant larger than the outside window openings, and glue them atop the frames. Then, trim out with thin strip wood.

gh_front_01

It looks just fine! Intentional, even. The two layers of cardstock, glued to the Plaskolite front and back, look believable. Even the little schmutzes of glue make sense in a marine environment (although they are easily cleaned up.)

gh_front_05.jpg

Here’s the whole structure-in-progress, including the new roof extension, which might be where the sleeping quarters wind up.

Ruby_101217

And here is the main — or one of the many — reasons I drive down to Santa Cruz each week: for Ruby, now four months old. She lights up a room, no batteries, routing or wires required.

Sea House Pavilion Sea Rise Remodel

11 Comments

stormy_100817

Turns out — after a lot of experimentation and test builds and weathering practice and pondering and faffing about — as much as I am captivated by abandoned miniatures, I do not wish to actually build one. I felt a bit sad when I realized this, but also relieved. The pavilion remodel still has sea level rise as a core premise, but now it’s more of a retrofitted, off-the-grid, self-sufficient adaptation that’s been going on for some years. With scavenging and memorabilia. The old skiff, with its faded Sea House emblem, stays. Stormy is just passing through :)